Macro Sensors LVDT Linear Position Transmitters Serve as Level Sensors In Gauging Tank Volume Level Changes
 | More News by Company: |  |
 |  |
| Press Release: | |
| Mar 24, 2014 — Configured with a float, Macro Sensors HSIR Series LVDT Linear Position Transmitters are serving as level sensors to measure liquid level changes from a few inches to several feet in gauging tank level volumes. In this LVDT level sensor configuration, a stainless-steel float coupled to a nonmagnetic stainless-steel rod is attached to the high-permeability, armature core of the LVDT. The 4 to 20-mA loop-powered LVDT position transmitter senses the position of the core and, therefore, the level of the float. Sensitivity to the change in level depends on the length of LVDT. While LVDT level sensors are used to measure level changes from 0 to 2, 12, or 20 in. (50, 300, or 500 mm), shorter lengths offer greatest sensitivity. In operation, as water level changes, the float moves up or down, raising the LVDT core along with it. A threaded stainless-steel rod, that protrudes from the other end of the core, carries two jam nuts that are used to adjust the position sensor output at the desired low water level. The nuts also prevent the core from falling out of the LVDT housing if the liquid level drops too low. A nonmagnetic clamp block attaches the stainless-steel body of the LVDT to a flat hook. The hook hangs the level-sensor assembly over the tank edge. Core position is sensed using magnetic induction. Electronics of the LVDT are hermetically sealed inside a stainless-steel housing for protection against water and other environmental elements. A Teflon liner inside the bore minimizes any friction to core motion. As there are no springs to fatigue or parts to wear out, the LVDT Linear Position Sensors are nearly friction free to offer infinite resolution and long term operation. For more information on this special configuration, contact the factory at positionsensors@macrosensors. For information on Macro Sensors 4-20 mA loop-powered LVDT, visit: http://www.macrosensors.com/HSI_HSIR_750.html . For a selection guide to LVDTs, visit: http://www.macrosensors.com/position_sensor_selection_guide.html . Capture to diagram: This diagram shows the LVDT level sensor attached to the side of a tank using a flat-hook assembly. The high-permeability core follows the position of the stainless-steel float. The LVDT electronics sense the core position using magnetic induction. Output is a 4 to 20-mA instrumentation current loop corresponding to the position of the core in the LVDT body. About Macro Sensors Macro Sensors’ extensive line of linear and rotary sensors are used for position measurement and feedback in a variety of industrial applications including factory automation, motion control systems, metal fabricating, automotive assembly as well as power plants, gas/steam turbines. Incorporated in 1994, the Company serves an international OEM and end-user customer base. On June 1, 2005, Macro Sensors was acquired by AST, manufacturer of state-of-the-art (Micro Electro Mechanical Structures) MEMS-based pressure sensors, transducers, and transmitters. Common applications of AST sensor products are in industrial OEM, hydraulic systems, fuel cells, medical gases, HVAC/R, refrigeration, oil & gas exploration/production, and off-road vehicles. For more information on AST products and technology, visit the AST website at www.astsensors.com. | ||
| For more information: http://www.macrosensors.com | ||
| Additional link: http://macrosensors.com/blog/view-entry/LVDT-Linear-Position-TransmittersServe-as-Level-/49/#.UzBBI6hdWDk | ||
| Tags: LVDT linear position sensors, linear position sensors, linear sensors |
| |
| Company Details: | |
| Contact: | Jean Carl | ||
| E-mail: | |||
| Company: | NewTek Sensor Solutions View Company Profile | ||
| Address: | workUS Route 130 North | ||
| Location: | workPennsauken, NJ 08110 United States | ||
| Phone: | workpref856-662-8000 | ||
| Web Site: | http://www.newteksensors.com | ||
| |
