Products / Services:
 Click on a category to see this company's product/service line for the chosen category. 
  
 
Dwyer Instruments, Inc.Michigan City, IN
 
E-mailE-mail CompanyComputer and GlobeVisit WebsitePhone
Phone: 219-879-8000
Fax: 219-872-9057
 
* Click on an image to enlarge it in a new window *
 These sensors are for use with Manometers, Magnehelic® Gages, Pressure Switches and other Controllers to pick up or sense static pressure drop across air filters and cooling coils, blower input and discharge pressures, etc. The angled tips shown have 4" insertion depth. Each has four radially drilled .040" sensing holes. All except Model A-303 mount in 3/8" hole in duct. For portable use, a magnet holds No. A-303 in place. No. A-305 is used where a very low actuation or sensing point is required on a pressure switch or gage or where response time is critical. No. A-307 and A-308 are suitable for use in low velocity systems or where the need for accuracy is less critical.
Get a Quote View Literature
 
   
 Static pressure tip, for 1/4" metal tubing connection.
Get a Quote View Literature
 
   
 Static pressure tip, for 3/16" and 1/8" ID plastic or rubber tubing.
Get a Quote View Literature
 
   
 Portable static pressure tip, for 3/16" ID rubber or plastic tubing with 4" insertion.
Get a Quote View Literature
 
   
 Static pressure tip, low resistance application, furnished with two (2) hex jam nuts and two (2) mounting washers for duct mounting and with 1/8" NPT pipe thread for pressure connection.
Get a Quote View Literature
 
   
 Outdoor static pressure sensor, provides average outdoor pressure signal for reference in building pressurization applications, includes sensor, 50 ft vinyl tubing, mounting bracket and hardware.
Get a Quote View Literature
 
   
 Static pressure fitting, for 1/4" metal tubing connection.
Get a Quote View Literature
 
   
 Static pressure fitting, for 3/16" and 1/8" ID plastic or rubber tubing.
Get a Quote View Literature
 
   
 Flange for mounting A-301, A-302, A-307, A-308 or 1/8" dia Pitot tubes with compression fitting when interior of duct is not accessible, aluminum, with gasket and sheet metal screws.
Get a Quote View Literature
 
   
 Static pressure pickup, for use in clean rooms, 100 micron filter picks up static pressure, stainless steel wall plate fits 2" x 4" electrical box, sealed with foam gasket, screws included. Barbed brass fitting holds 1/8" to 5/32" ID tubing.
Get a Quote View Literature
 
   
 Static pressure pickup, room mount with Delta style plastic enclosure fits 2" x 4" electrical box, mesh screen hides static pressure pickup port, clean connection to 1/8" to 5/32" ID tubing and pressure sensor. Sealed with foam gasket, screws included.
Get a Quote View Literature
 
   
 Static pressure pickup ceiling mount, plate rests on top of standard 3/4" thick ceiling tile while 100 micron filter faces down through 5/8" hole in tile, screws included for optional mounting to junction box, barbed fitting holds 1/8" to 5/32" ID tubing.
Get a Quote View Literature
 
   
 Static pressure pickup for roof/outside mount, NEMA 4X (IP66) rated structure withstands harsh environmental elements, structure is 3-5/8" across and 2-1/2" deep, EMT conduit fitting is 1/2", pressure connection is brass barbed fitting for 1/4" tubing.
Get a Quote View Literature
 
   
 Static pressure tip measures duct static air pressure, assembly includes 6" probe, silicon rubber house and screws, built-in surge damper ensures stable readings, pressure spike reducer can be added to further smooth over pressure fluctuations.
Get a Quote View Literature